as naudoju kazkoki is ebay ala usbasb v2.0. Programuoja jis tuos attiny. 
Ir megas... greicio kazkaip netikrinau.


avrdude -p atmega16 -P usb     -c usbasp  -v  -U flash:w:main.hex

avrdude: Version 5.11-Patch#7610, compiled on Aug 31 2011 at 08:02:19
          Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
          Copyright (c) 2007-2009 Joerg Wunsch

          System wide configuration file is "C:\WinAVR\bin\avrdude.conf"

          Using Port                    : usb
          Using Programmer              : usbasp
          AVR Part                      : ATMEGA16
          Chip Erase delay              : 9000 us
          PAGEL                         : PD7
          BS2                           : PA0
          RESET disposition             : dedicated
          RETRY pulse                   : SCK
          serial program mode           : yes
          parallel program mode         : yes
          Timeout                       : 200
          StabDelay                     : 100
          CmdexeDelay                   : 25
          SyncLoops                     : 32
          ByteDelay                     : 0
          PollIndex                     : 3
          PollValue                     : 0x53
          Memory Detail                 :

                                   Block Poll               Page 
                Polled
            Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages 
MinW  MaxW   ReadBack
            ----------- ---- ----- ----- ---- ------ ------ ---- ------ 
----- ----- ---------
            eeprom         4    10   128    0 no        512    4      0 
  9000  9000 0xff 0xff
            flash         33     6   128    0 yes     16384  128    128 
  4500  4500 0xff 0xff
            lock           0     0     0    0 no          1    0      0 
  9000  9000 0x00 0x00
            lfuse          0     0     0    0 no          1    0      0 
  9000  9000 0x00 0x00
            hfuse          0     0     0    0 no          1    0      0 
  9000  9000 0x00 0x00
            signature      0     0     0    0 no          3    0      0 
     0     0 0x00 0x00
            calibration    0     0     0    0 no          4    0      0 
     0     0 0x00 0x00

          Programmer Type : usbasp
          Description     : USBasp, http://www.fischl.de/usbasp/

avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp 
firmware update.
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% -0.00s

avrdude: Device signature = 0x1e9403
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be 
performed
          To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp 
firmware update.
avrdude: reading input file "main.hex"
avrdude: input file main.hex auto detected as Intel Hex
avrdude: writing flash (1838 bytes):

Writing | ################################################## | 100% 1.31s

avrdude: 1838 bytes of flash written
avrdude: verifying flash memory against main.hex:
avrdude: load data flash data from input file main.hex:
avrdude: input file main.hex auto detected as Intel Hex
avrdude: input file main.hex contains 1838 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.94s

avrdude: verifying ...
avrdude: 1838 bytes of flash verified

avrdude done.  Thank you.


 > Process Exit Code: 0
 > Time Taken: 00:02



On 2014.03.25 12:45, AMB wrote:
> neteisingai parasiau programatoriaus pavadinima :) vadinasi usbasp.
>
> "AMB" <jhlkjj@llkjhk.lt> wrote in message
> news:lgrjla$okr$1@trimpas.omnitel.net...
>> Turiu du programerius avrusb kitaicu gamybos. Naudojau su avrdude (per
>> WinAvr)  viskas buvo ok, kol prireike attiny. Niekaip nepalaike mazo SCK
>> greicio, tai tnaujinau softa programeriams (hex) ir perjungus jumperi ant
>> programerio dabar veikia su attiny. Dabar susiduriau su problema, kad koki
>> firmware berasau i programerius veikia tik mazu greiciu. Tarkim atmega8
>> irasydavo per koki 10sek, o dabar kokia minute. Ant programerio jumperis
>> slow sck uzstatytas, uzstacius iprastini rezima nemato isvis  atmegos.
>> Nezinau koki hexa naudojo kitaicai programeriams, gasl kas susiduret su
>> tokia problema?
>>
>
>

-- 
Bye, Levas

--
http://www.vabolis.lt