as darau pilna reseta, nauja firmware dedu ir tada configa keiciu.
"klaustukas" <omni@me.net> wrote in message
news:hgdhsk$5g3$1@trimpas.omnitel.net...
> Aciu, pabandysiu, o esamos konfiguracijos nereikia pasalinti? Jei taip,
> kokiu budu tai padaryti?
>
> Zilvis
> "Tomas J." <tomas@novena.lt> wrote in message
> news:hgdfkk$276$1@trimpas.omnitel.net...
>> Pabandyk
>>
>> uzeiname i dir-320:
>> telnet 192.168.1.1 (login: admin, passwd: admin)
>> sukuriame papke peers
>>
>> mkdir /tmp/ppp/peers
>> paleidziame vidini redaktoriu1. vi
>> ir paspaude raide i ikopijuojame (Copy/Paste) vat tai:
>> debug
>> /dev/usb/tts/0
>> 921600
>> mtu 1400
>> mru 1400
>> crtscts
>> noipdefault
>> ipcp-accept-local
>> lcp-echo-interval 60
>> lcp-echo-failure 5
>> usepeerdns
>> noauth
>> nodetach
>> user 'omni'
>> password 'omni'
>> connect "/usr/sbin/chat -s -S -V -t 60 -f /tmp/ppp/dialup.chat
>> 2>/tmp/chat.log"
>> Spaudziame ESC ir issaugome::w /tmp/ppp/peers/dialup
>> Iseiname is redaktoriaus
>> :q
>>
>> Vel paleidziame redaktoriu
>> 2. vi
>> '' ''
>> '' 'ATZ'
>> '' 'AT+CFUN=1'
>> '' 'AT+CGDCONT=1,IP,omnitel'
>> 'OK' 'ATD *99#'
>> 'CONNECT' ''
>> Vel ESC ir issaugome
>> :w /tmp/ppp/dialup.chat
>> :q
>>
>>
>>
>> 4. Sukuriame dar viena papke:
>> mkdir /tmp/local/sbin
>>
>> 5. Velgi paleidziame redaktoriu ir i ji ikopijuojame vat tai:
>>
>> #! /bin/sh
>> rmmod printer
>> insmod usbserial vendor=0x19d2 product=0x0015 maxSize=4096 <- cia savo
>> yrasai vendor produkt
>> DEVICE=1
>> while true; do
>> sleep 5
>> if [ -e /dev/usb/tts/${DEVICE} ]; then
>> echo 'modem found. call dialup'
>> mpcs -c /tmp/local &
>> sleep 2
>> pppd call dialup
>> killall -15 pppd
>> rmmod usb-ohci; sleep 2
>> insmod usb-ohci; sleep 2
>> else
>> fi
>> done
>> Spaudziame ESC ir issaugome:
>>
>> :w /tmp/local/sbin/post-boot
>> :q
>>
>> 6. Velgi paleidziame redaktoriu ir i ji ikopijuojame vat tai:
>>
>> #! /bin/sh
>> rmmod printer
>> insmod usbserial vendor=0x19d2 product=0x0015 maxSize=4096 <- cia savo
>> irasai vendor produkt
>> DEVICE=1
>> while true; do
>> sleep 5
>> if [ -e /dev/usb/tts/${DEVICE} ]; then
>> echo 'modem found. call dialup'
>> mpcs -c /tmp/local &
>> sleep 2
>> pppd call dialup
>> killall -15 pppd
>> rmmod usb-ohci; sleep 2
>> insmod usb-ohci; sleep 2
>> else
>> fi
>> done
>> Spaudziame ESC ir issaugome:
>>
>> :w /tmp/local/sbin/post-mount
>> :q
>>
>> 7. Sukuriame linkus i ka tik sukurtus failiukus
>>
>> echo /tmp/ppp/peers/dialup > /tmp/local/.files
>> echo /tmp/ppp/dialup.chat >> /tmp/local/.files
>> echo /tmp/ppp//tmp/local/sbin/post-mount >> /tmp/local/.files
>> echo /tmp/ppp//tmp/local/sbin/post-boot >> /tmp/local/.files
>>
>> 8. Suteikiame ka tik sukurtam skriptui paleidimo teises:
>> chmod +x /tmp/local/sbin/post-boot
>>
>> 9. Issaugome visa atlikta darba ir perkrauname DIR'a:
>> flashfs save && flashfs commit && flashfs enable
>> reboot
>>
>>
>>
>>
>> "klaustukas" <omni@me.net> wrote in message
>> news:hgdelb$ll$1@trimpas.omnitel.net...
>>> As naudojau WL500gpv2-1.9.2.7-d-r627M.trx
>>> ir dariau toki konfiga:
>>>
>>> telnet 192.168.1.1 (login: admin, passwd: admin)
>>>
>>> Sukuriame reikiamus katalogus:
>>> mkdir /tmp/local/sbin
>>> mkdir /tmp/ppp/peers
>>>
>>> 3. Sukuriame reikiamus failus:
>>>
>>> vi /etc/usb_modeswitch.conf
>>>
>>> CheckSuccess=2
>>>
>>> # ZTE MF633
>>>
>>> #
>>>
>>> # Contributor: Joakim Wennergren
>>>
>>>
>>>
>>> DefaultVendor= 0x19d2
>>>
>>> DefaultProduct= 0x2000
>>>
>>>
>>>
>>> TargetVendor= 0x19d2
>>>
>>> TargetProduct= 0x0031
>>>
>>>
>>>
>>> MessageEndpoint=0x01
>>>
>>>
>>>
>>> MessageContent="55534243123456782000000080000c85010101180101010101000000000000"
>>>
>>>
>>>
>>> # if that command doesn't work, try the other ("eject")
>>>
>>> MessageContent="5553424312345678000000000000061b000000030000000000000000000000"
>>>
>>> vi /tmp/local/sbin/post-boot
>>>
>>> #!/bin/sh
>>> chmod 777 /tmp
>>> usb_modeswitch
>>> sleep 5
>>> rmmod usbserial
>>> sleep 5
>>> s=0
>>> DEVICE=2
>>> insmod usbserial vendor=0x19d2 product=0x0031 maxSize=4096
>>> sleep 10
>>> while true; do
>>> if [ -e /dev/usb/tts/${DEVICE} ]; then
>>> echo 'modem on'
>>> /tmp/local/sbin/post-pppd start &
>>> sleep 20
>>> s=0
>>> else
>>> echo 'modem off'
>>> fi
>>> while [ -e /dev/usb/tts/${DEVICE} ]; do
>>> if [ -n "`pidof pppd`" ]
>>> then
>>> sleep 30
>>> else
>>> break #end while
>>> echo "pppd down"
>>> fi
>>> done
>>> echo ''
>>> if [ $s = 0 ]; then
>>> killall pppd
>>> killall -SIGHUP pppd
>>> killall /dev/usb/tts/*
>>> killall chat
>>> killall cat
>>> s=1
>>> else
>>> sleep 30
>>> fi
>>> done
>>>
>>> vi /tmp/local/sbin/post-pppd
>>>
>>> #! /bin/sh
>>> sleep 10
>>> pppd call dialup
>>> sleep 60
>>> cat /dev/usb/tts/1 &
>>>
>>> vi /tmp/ppp/peers/dialup
>>>
>>> debug
>>> /dev/usb/tts/2
>>> 921600
>>> mtu 1400
>>> mru 1400
>>> crtscts
>>> noipdefault
>>> ipcp-accept-local
>>> ipcp-accept-remote
>>> lcp-echo-interval 180
>>> lcp-echo-failure 3
>>> mppc
>>> maxfail 1
>>> usepeerdns
>>> defaultroute
>>> noauth
>>> persist
>>> holdoff 10
>>> user ''
>>> password ''
>>> connect "/usr/sbin/chat -s -S -V -t 60 -f /tmp/ppp/dialup.chat
>>> 2>/tmp/chat.log"
>>>
>>> vi /tmp/ppp/dialup.chat
>>>
>>> '' ''
>>> '' 'ATZ'
>>> '' 'AT+CFUN=1'
>>> '' 'ATQ0 V1 E1 S0=0 &C1 &D0 +FCLASS=0'
>>> '' 'AT+ZSNT=0,0,1'
>>> '' 'AT+ZOPRT=5'
>>> '' 'AT+ZSTART'
>>> '' 'AT+CPBS="SM"'
>>> '' 'AT+CPMS="SM","SM",""'
>>> '' 'AT+CGDCONT=1,"IP","omnitel"'
>>> 'OK' 'ATD *99#'
>>> 'CONNECT' ''
>>>
>>> 4. Viska issaugom su funkcijom:
>>> echo /tmp/ppp/peers/dialup > /tmp/local/.files
>>> echo /tmp/ppp/dialup.chat >> /tmp/local/.files
>>> echo /etc/usb_modeswitch.conf >> /tmp/local/.files
>>> chmod +x /tmp/local/sbin/post-boot
>>> chmod +x /tmp/local/sbin/post-pppd
>>> flashfs save && flashfs commit && flashfs enable && reboot
>>>
>>> "Tomas J." <tomas@novena.lt> wrote in message
>>> news:hgcvjh$7p3$1@trimpas.omnitel.net...
>>>> Viskas gerai, as truputi skriptus pakeiciau nei standartiniai,
>>>> pasileidzia omni connectas tiek isjungus ijungus dlinka, tiek istraukus
>>>> ir atgal ikisus modema.
>>>>
>>>> "klaustukas" <omni@me.net> wrote in message
>>>> news:hgcojq$s84$1@trimpas.omnitel.net...
>>>>> Tomai, tureciau tau klausima: kaip tau startuoja 3G po isjungimo is
>>>>> el. tinklo? Nes pas mane kaipo ir veikia bet jei isjungiu dlink'a is
>>>>> rozetes ir vel ijungiu per telnet matau usb device error'a po keliu
>>>>> software'iniu restartu- pasileidzia.. Butu kokiu minciu? Aciu.
>>>>>
>>>>> Zilvis
>>>>>
>>>>> "Tomas J." <tomas@novena.lt> wrote in message
>>>>> news:hgclkm$nnb$1@trimpas.omnitel.net...
>>>>>> Kaip cia pasakius apie ju darba, pvz. dlinko DIR-320 firmwaras su 3G
>>>>>> labai nepatiko, stabilumo nulis, perrasius asuso firmwara i ji ir
>>>>>> paburus truputuka dirba stabiliai.
>>>>>>
>>>>>> "Yksas" <karosas_istrinti@gmail.com> wrote in message
>>>>>> news:hgb3cq$lsh$1@trimpas.omnitel.net...
>>>>>>> rasiau, kad pradziai reiktu su 3G, o uz metu kokiu su 4G
>>>>>>> Taip kad per metus tiktai tuos draiverius parasys entziastai :)
>>>>>>> Dabar idomiausia, ar dirba jis su 3G modemais?
>>>>>>> Nes skaiciau, kad nauji routeriai jau defolt dirba su 3G modemais
>>>>>>> naudodami gimtaja firmware
>>>>>>>
>>>>>>>
>>>>>>> "RolF2" <123@123.123> wrote in message news:hg92cf$hqf$1@trimpas.om
>>>>>>> nitel.net...
>>>>>>>> RT-N16 sukasi 2.6 kernelis linuxo , ant wl500 - 2.4 . jei sugebesi
>>>>>>>> susikompilint driverius mezono jam - kodel gi ne :)
>>>>>>>>
>>>>>>>>
>>>>>>>> "Yksas" <karosas_istrinti@gmail.com> wrote in message
>>>>>>>> news:hg8j8q$2j9$1@trimpas.omnitel.net...
>>>>>>>>> Noriu pradziai per Asus routeri pasileistiOmni Connect(3g), veliau
>>>>>>>>> MEZON (4G)
>>>>>>>>>
>>>>>>>>> http://mezon.projektas.lt/ raso, kad tinka WL-500gp, WL-500gpv2
>>>>>>>>> arba WL-500W
>>>>>>>>> Atsirades yra modelis Asus RT-N16. Ar kazkas susidure su siuo
>>>>>>>>> routeriu, ar iseina ji perdirbti?
>>>>>>>>> Ar galesiu ji pamaitinti 3g ir 4g internetu, kad jis man per WI-FI
>>>>>>>>> interneta skleistu po visa nama?
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>>
>>>
>>
>>
>
>
>